Liebe Leute! Ich habe ein riesiges Problem. Ich habe es auf meinem PC zu installieren (HP Notbook, Win10, 64 bit) Ich schaffe es einfach nicht! Java ist installiert, aber ich weiß nicht, ob die Kommunikation mit MRL klappt. Oder wo die Fehler liegen könnten. Ich bin kein IT-Profi

Grüße,

Roger, Deutschland

MaVo

5 years 6 months ago

===== English version below =====

 

Hallo Roger,

wenn du irgendeine sinnvolle Art von Hilfe bekommen willst, musst du schon etwas genauer werden.

Wie weit bist du gekommen?

Startet MRL überhaupt?

Was ist/sind die Fehlermeldung(en) (wenn vorhanden)?

Hast du auch 64bit Java installiert (cmd: java -version)?

...

Du siehst, es gibt viel zu viele Möglichkeiten, um dir hier eine richtige Hilfestellung zu geben.

Zum Schluss noch: Deinen doppelten Post habe ich aufgeräumt und ich würde dir wirklich empfehlen nach Möglichkeit auf Englisch zu fragen, das ermöglicht deutlich mehr Leuten dir zu helfen.

Viele Grüße,

MaVo (auch Deutschland)

 

===== English version =====

Hi Roger,

you have to be a little more specific if you want any helpful advice.

How far did you get?

Does MRL even start in the first place?

What error message(s) did you get (if any)?

Did you install 64bit Java for your system (cmd: java -version)?

...

There are too many possibilities to give you any helpful advice right now.

btw: I cleaned up your double post & I strongly recommend asking for help in English, this way a lot more people are able to help you.

Regards,

MaVo (Germany - as well)

I did help him a bit through remote desktop, but the first error was, you didnt put mrl in C:\mrl

next, you said you made the servo work, but it wasnt that good. Did you start the inmoov script or did you start mrl with the java -jar myrobotlab.jar command?

After that did you start an arduino service and copied the mrlcomm.ino to the arduino? Could you connect to that arduino?

Next you should have setup a servo service, add the servo to the right pin and then enable the servo? Did you use the slider to confirm that the servo was working?

 

Gr. Wilco

If you want i could help you with remote desktop again, but my time is getting a bit more limited due to the upcoming makerfaire and my own programming.

Hallo Wilco,
Danke für die Antwort. Ich weiß wirklich nicht deine Zeit. Aber danke für dein Angebot, es noch einmal zu empfehlen.
 
Nun, leider bin ich nie weiter gekommen, als MRL zu starten. Ich kann einen Port in MRL oder die mrlcomm.ino auf den Arduinos integrieren.
In den Skripten von Arduino werden die richtigen COM-Ports (4 + 5) eingegeben, die Konfiguration wird auf FULL gesetzt
Die Arduino-Software erkennt die Arduinos und COM-Ports, aber die Kommunikation scheint nicht zu funktionieren
 
Es wurde einige Fehler gefunden (zB hs_err_pid13004). Weiser weiß ich nicht, war diese Fehler oder wenn ich sie kenne
 
Es scheint viele Fehlerquellen zu geben ...
 
Wie gesagt, ich möchte deine Zeit nicht wirklich bezeugen.
Auch nur wenn du wirklich Zeit hast ...
 
Freundliche Grüße,
Roger

Hallo und danke für die Antwort!

Danke auch für´s aufräumen...

1. Java it installiert, MRL ist installiert

2. MRL sartet und schließt sich dann wieder

3 Es tauchen mehrere Fehlermeldungen auf (hs_err_pid13004 z.B.)

4. Ja, Java 64bit ist installiert

Genauer kann ich es leider nicht beschreiben.

Ich habe damit vor mehr als einem halben Jahr für mich völliges Neuland betreten und hab mich so weit es ging durchgearbeitet. Es gab hier und da auch mal Erfolge, aber...na ja

Veilleicht hilft das weiter

Gruß, Roger

PS: Ich werde versuchen künfige Posts in Englisch zu verfassen 

I am tonight (friday) available, i think you didnt copy mrlcom.ino to the arduino.

But we can take a look at it. No problem.I downloaded the right java, the right mrl (manticore) and you should have installed mrlcomm.ino on the arduino (the right version). If you downloaded the latest nixie version from here the arduino code wont work with manticore (downloaded from inmoov.fr).

Anyway no worries, we will get you up and running.

===== English version below =====

Ich würde gerne einmal den Log sehen wollen.

Entweder als noWorky (-> link), als Upload hier oder auch als email (z.B. über das Kontakformular).

Für alles InMoov-spezifische wird dir aber @wvantoorn wahrscheinlich besser weiterhelfen können.

(Aus persönlichem Interesse: Aus welcher Region kommst du? : ) )

~MaVo

 

===== Englisch version =====

If possible, I would like to see your logfile.

You can for example send a noWorky (-> link) (best option). If MRL instantly closes, you can also upload your log here or send one of us an email.

If you have InMoov-specific questions, @wvantoorn will be more helpful than me.

~MaVo